While you can wax the film, be sure the product you are using doesn’t contain Naphtha or Kerosene in concentrations over 5%, and avoid waxes that contain dyes. For best results, we recommend using our XPEL Flawless Finish Paint Protection Film Sealant or XPEL Ceramic Boost. This product has been specially formulated for use with polyurethane paint protection films to provide the maximum protection and gloss, while containing no ingredients that would cause discoloration over time.
Yes. Paint protection film can be applied to most smooth painted surface.
Our ULTIMATE PLUS Series Films are warrantied for 10 years. This warranty covers: yellowing, delaminating, cracking, peeling, bubbling, and more. More information on the warranty can be found on our Warranty Information page
Yes. The process is the same as with regular paint: wet the surface with a lubricant such as XPEL Detail Spray or soapy water and then gently rub the surface with the clay bar. For stubborn insect, bird dropping, or hard water stains, use an all-purpose degreaser such as Simple Green as the lubricant for the detailing clay.
No special maintenance is required for XPEL ULTIMATE PLUS. However, the film will last longer and will be easier to clean if treated twice a year with XPEL Flawless Finish Paint Protection Film Sealant.
Any of our films can be installed on Chrome, though the finish will look slightly different than if left unprotected. We recommend having your installer apply a small swatch to the desired surface so you can see what it looks like before deciding.
XPEL ULTIMATE PLUS is warrantied for 10 years against a range of issues including yellowing. More information about the warranty can be found on our Warranty Information page
Yes, we have a gloss black paint protection film. Visit "Shop" above and click XPEL ULTIMATE PLUS BLACK
The clear coat is the self-healing layer and is approximately 13 microns thick. If that layer is penetrated, the film will not heal.
Not at this time, please contact customer support for more information
Yes, our pre-cut kits are available for sale on our website, www.xpel.com, or by calling our customer support team at 1-210-678-3700. However, as installation can be quite difficult without previous experience or formal training, we recommend having installation performed by one of our Factory Trained Installers. To find an installer nearest you please visit our Installer Locator to find an installer near you.
No, XPEL Paint protection film cannot be installed on your windshield. Due to the impact absorbency of paint protection film, the refractive index of the film is too different from that of the windshield. Because of this difference, putting the two together causes a distortion when looking through the glass that would be unacceptable to the vehicle’s occupants.
Yes. We have installers available worldwide. Please visit our Installer Locator to find an installer near you.
Yes, TracWrap can be applied to vinyl.
Because the product is installed by independent installers, cost varies greatly based on location, labor rates, and installer experience. To get an estimate from a local installer nearest you, please visit: XPEL Installer Locator
It is always best to contact your XPEL installer first and explain your concerns. We do our best to maintain a network of installers that stand behind their work. If after doing so, your installer cannot or will not address your concerns to your satisfaction, please contact our customer service team for assistance. They will get you in touch with the XPEL Representative for your area who will work to find a solution to the issue.
Yes. Most smooth painted surface can be covered with paint protection film.
Paint protection film can be applied on any smooth painted surface. However, given the tight tolerances on weight, balance and other factors on some aircraft, it is highly recommended to consult with the manufacturer of the airplane for strict guidance.
If you want to protect your STEALTH paint protection film, we recommend using our XPEL Flawless Finish Paint Protection Film Sealant or XPEL Ceramic Boost. When applying the sealant, work in small areas thoroughly wiping away all excess before moving on to the next section. Test an inconspicuous spot for application technique as installation is difficult due to the satin finish.
Yes, but please wait at least 48 hours after installation to allow the film to dry completely.
Acry-solvent, or any other Xylene based solvent, will not harm the film unless left sitting saturated in it for an extended period. To use this type of solvent on the film (for removing stains, etc.) wet a microfiber towel with the product and wipe the film for one or two minutes. If the stain remains, allow the solvent to evaporate and then repeat the process.
Yes, while XPEL can be installed on marine boats and watercraft, please review the warranty for applicable surfaces
Yes, pressure washers can be used on XPEL paint protection films, provided the film has completely dried after installation (typically 48 hours) and provided the high-pressure water is not pointed directly at the edges of the film.
Other than the simplest body panels, application of paint protection film is a process which requires a good deal of experience and training to obtain satisfactory results. The compound curves present on most surfaces require the film to be stretched and compressed in a very controlled way to ensure proper adhesion without distorting the adhesive. As such, it is highly recommended that the film is professionally installed.
It depends on the coating. Some may deepen the finish while others may add unwanted gloss. We recommend testing the coating on a swatch of unused film or in an inconspicuous area before coating a protected panel. We recommend using XPEL FUSION PLUS Ceramic Coating, our ceramic coating was designed with paint and XPEL Paint protection film in mind.
It is highly unlikely for paint protection film to harm OEM paint. Paint systems used on modern assembly lines today produce a minimum bond strength of 16 MPa and maximum of 25 MPa between the panel and the paint depending on color, iridescence and the system used. Our film’s bond to the painted surface at normal state (immediately following installation) is .0753 MPa. Even after years of heat and sun, the bond between the film and the paint increases to only 0.17 MPa. What that means is in the absolute worst case scenario, the bond of factory paint to the panel is over 94 times stronger than the bond of our film to the paint. In the best case, the paint is 332 times stronger. That being said, it is still recommended to have a professional remove the film in accordance with our published guidelines.
Yes. XPEL film can be applied over a vinyl wrap or graphics. However, if there are any hard edges that film must cross (as in the case of stripes), it could result in some air being trapped along that edge.
Yes, XPEL can be installed on your cars headlamps and fog lamps
We recommend using the XPEL Rinse Free Car Wash, combined with the XPEL Detail Spray and Ceramic Boost for increased cleanliness and slickness
Yes. Though you can install the film over any quality of touch-up, the best possible appearance will be obtained if the touched up area has been color-sanded smooth and buffed after the application of the paint.
Yes. XPEL ULTIMATE PLUS can be applied to any smooth surface, though care should be taken around any electronics and/or switches so that installation fluids aren’t allowed to get into sensitive areas.
Yes, most factory paint is fully cured before the car ever leaves the assembly line.
XPEL Film Cleaner is generally designed to remove dirt, grime and oils from paint protection film that lead to yellowing over time. To remove stains from other substances such as insects, bird droppings or other compounds, use acetone or lacquer thinner with a soft microfiber cloth.
While the edge of the film can be seen from certain angles, people generally do not notice it unless they are looking for it. However, if the car is dirty and dust and dirt can collect along the edge of the film, it will be more noticeable. Once the car is cleaned, it will be once again difficult to detect unless looking for it.
The self-healing clear coat of our ULTIMATE PLUS and STEALTH films is designed to repair itself from swirl marks and light scratches from car washes, etc. If a piece of debris has penetrated all the way through the clear coat on the film, it will not self-heal. The only way to fix this would be to have the piece of film replaced.
If there is left over adhesive upon removal, you can use a general purpose adhesive remover, often found at your local auto parts or home improvement store.
The XPEL ULTIMATE PLUS Film Series warranty is transferable to another owner with proof of purchase.
No, the film once applied and removed cannot be reused.
Any of our paint protection films can be installed on aluminum or brushed metal, though they may change the appearance to some degree depending on the film you choose. We recommend having your installer apply a small swatch of the film to the surface in question to determine the appearance prior to full installation.
We recommend using our XPEL Flawless Finish Paint Protection Film Sealant. This product has been specially formulated for use with polyurethane paint protection films to provide the maximum protection and gloss, while containing no ingredients that would cause discoloration over time. We also recommend XPEL Detail Spray and/or Ceramic Boost for added slickness and ease of cleaning.
Waxes, sealants and protectants are typically designed to reduce the surface energy of the paint, making them easier to clean etc. A reduction in surface energy will reduce the film’s ability to adhere to the paint and could cause long term adhesion issues. Because of this, we generally recommend removing these types of products before installation. If these types of coatings are to be used, we recommend applying them AFTER installation of our paint protection film.
Yes, Coatings can be applied to the films. Adding a coating does not stop the film from self-healing. Coatings can add a protective layer over the film, which depending on the coating can provide different properties (Please contact your installer or coating company for more information). That additional coating layer, depending on the coating applied, may or may not self-heal. Once the coating wears down and deteriorates, the self-healing qualities of XPEL ULTIMATE PLUS and STEALTH will remain. We recommend XPEL FUSION PLUS Ceramic Coating. Our ceramic was specifically formulated for your vehicles paint and XPEL Paint protection film.
We would not recommend this, as it may result in poor adhesion to the painted surfaces. Professional removal of the ceramic coating is recommended. You may install XPEL FUSION PLUS on top of your XPEL Paint Protection Film. Check with your local installer for more details.
Please see the diagram on www.xpel.com/care and be sure to use a steamer or heat gun to soften and warm the adhesive. This will yield the best possible results and will leave little if any adhesive behind. Any traces of residue left behind can be removed with any commercially available adhesive remover that is safe for automotive paint.
We offer pre-cut rocker panel coverage for most trucks and SUVs that can be professionally installed by our independent dealer network. Visit our Installer Locator for an installer near you for a quote.
We also make a rocker panel DIY kit to help protect your rocker panels. This product is available in our XPEL ULTIMATE PLUS film or our XPEL ARMOR film. ULTIMATE PLUS is our clear self-healing paint protection film, while ARMOR is a rugged film that is black and has texture similar to a spray in bed liner.
Yes, assuming you and the installer are both comfortable with the risk, there is nothing about the film that would prevent this from being done. We also have designs for most body panels on nearly every vehicle, which would allow installation without dismantling the vehicle.
Yes, you can install a vinyl on top of the film. We recommend waiting 48 hours after installation before doing so. You may also remove the stripe without damaging the film, if removed properly.
No. We do not currently offer a windshield protection film.
This is a very common occurrence with Paint Protection Film of all brands. It has to do with the difference in refractive index between the layer of film and the paint on the car. It is most noticeable on compound-curved surfaces because the film must be stretched over these areas to allow it to be installed without wrinkles. When the film is stretched, it becomes slightly thinner in those areas which causes the phenomenon seen through polarized glasses.
It can also occur on flat surfaces when the installer needs to use a drying solution (as opposed to a slip solution) such as alcohol and water to get the needed bond to the paint. This is due to the difference in viscosity of the fluids and their effect on the adhesive’s properties.
Polarized glasses have this effect on several different multi-layer surfaces (not just paint protection film) made of glass or plastic.
Yes. XPEL can be installed on your cars headlamps and fog lamps
When using the wet application technique, this is normal. The fog is the result of the alcohol/water solution evaporating from beneath the plastic. The water vapor that is produced results in a hazy appearance for several days. The haze will clear as the vapor dissipates.
We have found that the wet installation yields the best-looking installation with the least amount of difficulty in most cases. On larger headlamp pieces, bubbles and improper alignment of the material are far less likely using the wet installation method. However, on smaller pieces, such as fog lamps, the dry installation method is sometimes easier. This is especially the case if the lamp is spherical in shape.
It is imperative that a hairdryer or heat gun is used in this area to seal the edges. The heat serves two purposes. First, it helps evaporate the remaining alcohol/water solution from under the edges, and second it makes the plastic more pliable so that it can contour to the shape of the light. Be careful if you are using a heat gun to warm the plastic. It takes only a small amount of heat to apply the material. If you apply too much heat you can damage the surface of the plastic.
The removal process is just a matter of warming the plastic and peeling them off. They will require some muscle to get them off, but they normally peel off without any residue left on the lens. If any adhesive at all remains behind, it may be removed by simply rubbing it with your thumb. The adhesive will then ball up and roll off.
We offer a transferable lifetime warranty on the following lines of our window film (CS, HP, XR and XR PLUS). The warranty covers against cracking, peeling, bubbling, delamination, fading and color change for the life of the film. The warranty is transferable and will continue with the car even in the event the ownership change.
Yes, we introduced XPEL VISION in early 2019 and has been an industry leader since its launch. Visit VISION Architectural Film
Our window film is designed to with a very strong adhesive for durability, upon removal of the window film the adhesive may not fully transfer to the film and will remain on the glass. Your installer will be able to remove this during the installation process.
We do not recommend installing XPEL PRIME Series Window Film to Plexiglass or plastic windows.
The many benefits of window film include heat reduction, eye comfort, UV protection, aesthetics, and increased safety, privacy, and energy savings.
The moisture that remains between the film and the glass after installation can cause a hazy, streaky, blotchy appearance. It takes several days for the film to completely cure. The remaining moisture will evaporate through the film; depending on the type of film, this process may take a couple of days, or even a couple of months (depending on your climate). When the water evaporates completely, your windows should have excellent clarity.
No. Window film is installed on the inside of the glass. This allows for maximum durability
After window film installation, wait a week before cleaning the inside of the window where the film was installed. After a week, use XPEL Anti-Static Window Film Cleaner with a soft microfiber cloth. Never scrape the film with any type of blade or clean your tinted windows with anything abrasive, as it will scratch the film.
We recommend that you leave your vehicle windows rolled up for at least 24-36 hours after window film has been installed. This allows the film to cure and adhere to the glass before the window is moved.
Yes. The same sun that brightens your car’s interior can be detrimental to fabrics, leather, dashboard, and other interior surfaces. Ultraviolet rays are the main cause of both fade and deterioration. XPEL window films can screen up to 99% of the damaging UV rays that can fade surfaces.
In the presence of moisture, the ANTIMICROBIAL SURFACE PROTECTION additive gradually releases zinc pyrithione, which can strongly bind to cellular enzymes of the microbe while inhibiting enzyme activity in cell walls, membranes, and nucleic acids. Microbes have a negative surface charge, so zinc pyrithione with a positive charge are drawn towards them, disturbing their electrical balance. This results in the bursting of the cell walls, destroying the microbe.
RX can safely be cleaned with a wide variety of manufacturers bleach based and non-bleach-based cleaners as well Quaternary Ammonium Germicidal Wipes, from PDI, Safe Tec, Steris, Jet, and others. i.e., alcohol wipes, bleach wipes, germicidal wipes. Avoid hydrogen peroxide.
Yes, we recommend using XPEL Installation Gel for the application of the RX.
Due to the various surfaces this can be applied to, we recommend the least aggressive cleaning method to ensure no damage to the surface.
The time can vary depending on the surface that RX was applied to and climate conditions. For most surfaces, please allow 24-48 hours before heavy usage.
We would recommend something with a smooth uniform surface, such as glass, display screen, painted surface, etc. RX10 is designed to be optimal on completely flat surfaces and increases impact protection. RX8 is designed to conform with curved geometries and has more flexibility than RX10.
Yes, RX can be used both indoors and outdoors if RX is installed correctly and on proper surfaces.
RX can be removed in similar fashion to our paint protection films, use caution with removal on different substrates. Simply pull the film towards yourself at a 45-degree angle from the surface. Full removal instructions available on www.xpel.com
If installing on a non-electronic surface, you can use isopropyl alcohol to remove any excess installation fluid and to squeegee the edges, to ensure they are secure on the surface.
Yes. The same sun that brightens your car’s interior can be detrimental to fabrics, leather, dashboard, and other interior surfaces. Ultraviolet rays are the main cause of both fade and deterioration. XPEL window films can screen up to 99% of the damaging UV rays that can fade surfaces.
ATP is short for adenosine triphosphate; it is an organic molecule that is used by living cells as their main source of energy. Animal, plant bacterial, yeast and mold cell products and break down ATP to drive several biological processes, and the main energy transfer molecule in the cell. The presence of ATP on a surface indicates that the surface has not been adequately cleaned and has the potential to harbor and support bacterial growth. The residue may also contain hazardous material including protentional allergens. Therefore, ATP is an ideal indicator of surface cleanliness.
Yes, these are available on our website, www.xpel.com/RX
Yes, we offer RX in both a gloss and matte finish as well as two different thickness variations. RX10 with an extra impact layer for flat surfaces and RX8 with flexibility and the ability to install on complex surfaces such as door handles and other surfaces.
RX has not been FAA approved, we cannot endorse application on aviation equipment at this time.
There are endless possibilities with RX Anti-Microbial Surface Protection Film to include, but not limited to: Hospitals, Urgent Care Facilities, Out-Patient Surgery Centers, Food Industry, Residential and Commercial, and more
Full warranty details for RX can be found at www.xpel.com/warranty-information
You can use the same test equipment mentioned above to test the ATP on the surface, Hygiena SystemSure Plus ATP Monitoring System, accompanied with Hygiena Ultra Snap Surface ATP Test Device Swabs.
Light surface scratches will self-heal when external heat is applied.
FUSION PLUS uses Silicon Dioxide technology. It is a complex chemical matrix that is unique to us. A combination of several technologies that cross-link very strongly to form a strong 9H coating.
Ease of maintenance, hydrophobic properties, and self-cleaning properties.
FUSION PLUS Ceramic Coating warranties are available at www.xpel.com/warranty-information.
Cure times vary depending on which coating you have had applied to your vehicle. Please check with your local dealer or on our technical data sheets available on our website.
Yes, XPEL FUSION PLUS MARINE is designed to help protection your watercrafts surface.
Yes, we provide a FUSION PLUS ceramic coating specifically designed for aircraft applications.
Warranty terms vary depending on your applied coating, please visit www.xpel.com/warranty-information for full warranty details and coverages.
This combo is extremely common. The car enthusiast is after that best-case scenario type of maintenance. Having PPF and ceramic coating will keep the vehicle protected from rock chips, road debris, and more while having all the benefits of a ceramic coated car. Those benefits being hydrophobic properties, self-cleaning, and an increased gloss and depth appearance.
Yes, you can apply FUSION PLUS PAINT & PPF to the STEALTH film. It will not make the surface glossy; it will enhance the depth of the matte finish.
Yes. The same sun that brightens your car’s interior can be detrimental to fabrics, leather, dashboard, and other interior surfaces. Ultraviolet rays are the main cause of both fade and deterioration. XPEL window films can screen up to 99% of the damaging UV rays that can fade surfaces.
9H hardness is a rating based on the Pencil Hardness Test, commonly used by manufacturers of clear and pigmented surface coatings. The Pencil Hardness test is used to determine the scratch resistance of a coating surface by using pencils to scratch the surface and rate the scratch resistance in relation to that pencils hardness and other materials of similar hardness.
We offer a full line up of premium ceramic coatings. Visit www.xpel.com/fusion-plus for a full list of our ceramic offerings.
No, we do not offer a self-healing coating currently. We do have our paint protection films that feature self-healing features.
FUSION PLUS GLASS is not a windshield protection film; it does not prevent stone chips. It helps make the glass surface more hydrophobic
We would recommend using XPEL Anti-Static Window Cleaner.
Yes, PLASTIC & TRIM helps prevent fading due to UV rays. It also enhances and rejuvenates the plastic and trim surface.
We would recommend using XPEL Rinse Free Car Wash
Yes, this product is designed for the high heat temperature for your vehicles wheel and caliper surfaces.
No, factory interiors should not discolor, our product allows the material to breathe, retaining its natural feel and retaining its original look.
FUSION PLUS UPHOLSTERY helps prevent interior surfaces from stains and spills.
FUSION PLUS UPHOLSTERY can be applied to your automotive Fabric, Carpet, Leather and Vinyl. Do not use on Alcantara and Suede surfaces.
XPEL FUSION PLUS UPHOLSTERY helps protect your interior surfaces, (fabric, carpet, leather, and vinyl) from spills and stains. It is not a waterproofing coating.
Yes, UPHOLSTERY, can be used on carpets. All interior must be professionally cleaned before applying UPHOLSTERY. Avoid Alcantara and Suede surfaces.
FUSION PLUS MARINE will help prevent unsightly damage associated with UV Ray aging and fading colors.
Yes, FUSION PLUS MARINE works on paint and gelcoat surfaces for the watercraft industry.
Yes, you can use FUSION PLUS MARINE on your boat trailer to help protect it when launching your watercraft.
For the film to completely dry out, the weather conditions (cold vs. warm, non-sunny vs. sunny) will affect the total time. There may be small water beads and a slightly cloudy look till the film completely dries out. We advise to not clean the film for 30 days after installation to be safe.
Window film creates a more comfortable environment through consistent climate control by eliminating “cold wall” and “hot wall” problems. Rooms stay more comfortable in the summer and winter, be reducing “hot spots”, no matter where the sun is shining.
Yes. The same sun that brightens a room’s interior can be detrimental to fabrics, furnishings, artwork, and rugs. Ultraviolet rays are the main cause of both fade and deterioration. Window films can screen out 99% of the damaging UV rays that can fade richly colored furniture, tapestries, and artwork. Heat and light also play a part in fading but using window film to block nearly 100% of UV rays will increase the life of your personal property for years.
After window film installation, wait until the film is cured before cleaning the inside of the window where the film was installed. After a week, use XPEL Anti-Static Window Film Cleaner with a soft microfiber cloth. Never scrape the film with any type of blade or clean your tinted windows with anything abrasive, as it will scratch the film.
Film percentages stand for visual light transmission (VLT), or the amount of light that is allowed through the film. The lower the percentage, the darker the film. With modern advances in window film, you can have great heat rejection with lighter films, no need to have dark window tint to receive the heat rejection benefits.
The many benefits of window film include IR heat reduction, eye comfort, UV protection, aesthetics, and increased safety, privacy, and energy savings.
Our window film is designed to with a very strong adhesive for durability, upon removal of the window film the adhesive may not fully transfer to the film and will remain on the glass. Your installer will be able to remove this during the installation process.
We offer films that will give you daytime privacy, but current window film products do not offer nighttime privacy if the lights are on in your interior space. You do have the option to use a decorative window film, such as our white frost to achieve nighttime privacy, although you will not be able to see in or out during the day and night.
Yes, we do! Please check out the links in the header above for our VISION Security Line.
Yes, we offer security film for all applicable windows. Check with your local installer to see what available options there are for your home and/or office.
After window film installation, wait for the film to fully cure before cleaning the inside of the window where the film was installed. After a week, use XPEL Anti-Static Window Film Cleaner with a soft microfiber cloth. Never scrape the film with any type of blade or clean your windows with anything abrasive, as it can scratch the film.
Yes, we offer anti-graffiti window film for your home and or office.
Yes, we offer anti-graffiti window film for your home and or office.
Yes, we offer decorative window film for your home and or office.
Yes, our decorative films can be installed in your bathroom. Our White Frost film is a popular window film for shower doors or windows for a custom look and privacy.
No, the decorative film is opaque and does not offer visibility when looking through the film.
No, if installed properly, your installation team will bring the necessary materials and tools to prevent mess in your space.
Senior VP & Chief Financial Officer
Mr. Wood has served as the Company’s Chief Financial Officer since June 2016. Mr. Wood is responsible for the Company’s Finance/Accounting, Risk Management, Treasury Management, Investor Relations and Corporate Development functions. Prior to joining the Company, Mr. Wood served as Vice President – Dispensing Operations for Optum Rx (previously Catamaran Home Delivery), Chief Financial Officer of PTRX, Inc., a pharmacy benefits and prescription home delivery company and served in various executive finance roles with AT&T (formerly SBC Communication, Inc.). Prior to this, Mr. Wood served as an Audit Manager for Ernst & Young.
Mr. Wood holds an MBA from University of Texas – Dallas and a Bachelor of Science – Accountancy degree from Southern Illinois University – Edwardsville. Mr. Wood also holds Certified Public Accountant and Chartered Global Management Accountant designations.
VP, Asia Pacific
Mr. West joined XPEL in 2021 and currently serves as the VP of Asia Pacific where he oversees all of XPEL’s business affairs in the region.
Prior to his current role, Mr. West was the Director of Automotive Films, followed by Sr. Director of Install Operations. He has been involved with the automotive aftermarket industry for 20 years and owned a successful shop in Anchorage, Alaska. He also founded Tracwrap, which was sold to XPEL in 2013.
He has traveled the world installing, training, and consulting businesses in the automotive films industry. Mr. West holds a bachelor’s degree in civil engineering.
VP, People Services
Ms. Steiner recently joined the Company, serving as VP of People Services.
Ms. Steiner is responsible for shaping the Company’s people strategies and growing the global capabilities of the Company while aligning it with the overall strategic direction of the organization.
Ms. Steiner brings over 20 years of multi-industry, global HR experience. In her most recent role, she was responsible for leading HR for E. & J. Gallo’s US Sales Organization. Prior to that, she was VP of HR, Americas at Otis Elevators and spent 21 years at General Electric in HR and engineering leadership roles.
Ms. Steiner holds a bachelor’s degree in chemical engineering as well as an MBA from The Pennsylvania State University.
VP, Revenue
Mr. Rimas recently joined the Company, serving as VP of Revenue. He leads the global sales team, partnership and commercial strategy.
Mr. Rimas was the President of Repairify, which empowers the vehicle-side repair professional with software, intelligence, and access to the proprietary Repair OnDemand marketplace. Mr. Rimas also has a wide range of experience in many segments of the automotive industry, including retail, financial services, aftermarket, and fleet services.
Mr. Rimas was the co-founder and Managing Partner of FM Capital, where he led and managed many disruptive automotive investments including Autoniq, Frontier Car Group, Vroom, Autopay, and Revolution Parts. Before FM Capital, Mr. Rimas was the Director of Operations of the Red McCombs Automotive Group where he also helped lead successful investments in both HomeNet Automotive (acquired by Cox Automotive) and ClickMotive (acquired by DealerTrack).
Mr. Rimas is the current Chairman of NitroFill and a former board member of ProCare Collision (acquired by Classic Collision). Mr. Rimas is also Managing Partner of AuctionXM, and an advisor to WarrCloud, Zohr, and NuBrakes. Recently, he joined the board of Work Truck Solutions, Vincue, and exited his vehicle reconditioning business (Streamline Recon) in a merger with SolutionWorks.
Mr. Rimas holds a bachelor’s degree in chemistry from Ball State University.
VP, Corporate Development
Mr. Mayall has worked for/with XPEL since 2000 and currently serves as XPEL’s VP of Corporate Development. He joined XPEL full time in 2016 when his businesses, PRO-TECT FILM and PROFORM, were acquired by XPEL.
Mr. Mayall has been involved in the film, adhesive and automotive aftermarket since 1993 where he started as an installer of window films and paint protection films. In 2004 he founded a film distribution and installation company, PRO-TECT FILM, where they grew to be the largest installer of automotive paint protection film and residential safety/security film in Las Vegas at the time it was acquired. During that time he was also co-owner of PROFORM, a design and software business that operated out of Las Vegas until the time it was acquired.
VP, Product
Mr. Joshi currently serves as XPEL’s VP of Product and has worked at XPEL since 2018. Mr. Joshi oversees Product Management, Manufacturing, Research & Development, Purchasing and Planning functions for the company.
Prior to joining XPEL, Mr. Joshi served as the Deputy General Manager at Garware Hi-Tech Films and oversaw the North American business for the company.
Mr. Joshi holds a Bachelor of Technology (B.Tech) in Mechanical Engineering from the College of Engineering, Pune (COEP) and a Master of Science (M.S.) in Management Science & Engineering from Stanford University.
VP, Services
Mr. Gotro joined XPEL in 2022 and currently serves as the VP of Services. In this role he is responsible for overseeing Dealership, Retail, OEM, Design and Training Operations.
Prior to joining XPEL, Mr. Gotro spent 17 years at entrotech in a variety of positions, including Director of OEM Integration and Director of Paint Protection Film. He also worked in consulting.
Mr. Gotro holds a bachelor’s degree in chemical and biomolecular engineering from The Ohio State University.
VP, Controller
Ms. Coffee joined XPEL in January 2008 and currently serves as the Company’s Controller. She is responsible for all Accounting, Treasury Management and Payroll functions for the company. Prior to joining XPEL, Ms. Coffee served as an Accounting Manager for Enterprise Rent-A-Car.
Ms. Coffee holds and M.Ed. from the University of Texas at Austin and a Bachelor of Science in Accounting from the University of North Texas. Ms. Coffee is also a Certified Public Accountant.
Senior VP, General Counsel
Mr. Awodiran recently joined the Company, serving as General Counsel and Corporate Secretary.
Mr. Awodiran is responsible for all legal and compliance matters affecting the Company, including managing the legal function, providing effective advice on Company strategies and their implementations, corporate governance and securities law compliance, Board and Board committee matters, commercial and corporate transactions, ethics, and compliance.
Prior to joining the Company, Mr. Awodiran served as Group Counsel, Securities and Corporate Law and Assistant Corporate Secretary for Ashland Inc., a global additives and specialty ingredients company. Before this, Mr. Awodiran served in various legal roles at Caterpillar Inc. during his 14 years, most recently as Senior Corporate Counsel, supporting the Industrial Power System Division’s global sales and marketing operations.
Mr. Awodiran holds an LL.M. from the University of Illinois at Urbana-Champaign and an LL.B. from the University of Ibadan, Nigeria. Mr. Awodiran obtained his US bar license from New York State.
VP, Operations
Mr. Alvarez joined XPEL in December 2017 and currently serves as the VP of Operations. In this role he is responsible for overseeing all manufacturing, quality, distribution, logistics, purchasing, and customer service functions within XPEL.
Prior to joining XPEL, Mr. Alvarez served in a variety of operational leadership roles within AT&T and KCI/ Acelity.
Mr. Alvarez holds a bachelor’s degree in finance from St. Mary’s University, and an MBA from Texas A&M University – San Antonio.
Chairman, President & CEO
Mr. Pape serves as XPEL’s Chairman, President and Chief Executive Officer and previously served in a variety of positions within the XPEL until his appointment as Chief Executive Officer in 2009.
Prior to joining XPEL in 2004, Mr. Pape was in technology consulting.
Mr. Pape has a Bachelor of Science degree from the University of Texas at Austin.
Mr. Pape has served on XPEL’s Board of Directors since 2010 and currently serves as the Chairman of the Board.
Director
Mr. North serves as CEO of Lazydays RV Holdings, Inc., a $1.3 billion leader in the RV industry providing RV sales, service, and ownership experiences. He previously served as CFO of global auto reseller Copart, Avis Budget Group and Lithia Motors, one of America’s largest automotive retail groups. While at Lithia Motors, Mr. North helped successfully manage the company’s financial transformation as Lithia grew from $2.1 billion in revenue in 2010 to $12.0 billion in 2018.
Mr. North has a deep knowledge of the automotive industry with proven experience in global retail operations, finance, acquisitions and integrations.
He earned a Bachelor of Science degree in Commerce with an emphasis in Finance from Santa Clara University.
Director
Mr. Klonne built a successful career from entry level sales to President and CEO. He played a major part and led the growth of Findley Adhesives from a $20 Million, regional company to a $300 Million global company which led to the ultimate sale of the company to Bostik, S.A.
Mr. Klonne served as CEO of Bostik, Inc, a subsidiary of Bostik, S.A., of Paris France, for nearly 15 years helping grow Bostik, Inc.’s revenue to $1 Billion with over 1,000 employees at 20 sites across North America, Latin America, Europe and Asia.
Mr. Klonne has served on XPEL’s board since 2017 and currently chairs the Audit Committee.
Director
Mr. Crumly has been investing in start-up companies and other entrepreneurial ventures for more than 30 years. Mr. Crumly has been involved in ventures ranging from consumer products to telecommunications from start-up to the transition to the public marketplace.
Mr. Crumly also has years of experience investing in various real estate ventures, from raw land to developed properties and also has interests in the timepiece and estate jewelry market.
Mr. Crumly graduated from Trinity University in San Antonio with a Bachelor of Science.
Director
Ms. Bogart serves as Senior Vice President, General Counsel, Secretary and Corporate Responsibility of Winnebago Industries. Prior to joining Winnebago Industries, Bogart was Senior Vice President, General Counsel and Compliance Officer, Corporate Secretary at Polaris Industries where she joined in November 2009. Previously, Bogart was General Counsel of Liberty Diversified International; Assistant General Counsel and Assistant Secretary at The Toro Company; and a Senior Attorney for Honeywell Inc.
Ms. Bogart is an accomplished business executive who is known for partnering with senior management to achieve long-term strategic transformational goals, working with public company Board of Directors, corporate governance, corporate social responsibility, risk management, strategy, and mergers and acquisitions.
Ms. Bogart has a Bachelor of Arts degree and Juris Doctorate with Distinction from the University of Iowa.